Specials

• for damage-free loosening and tightening the plastic plug on the starter battery
• special slot profile for battery plug
• universally applicable due to its low height
• thus allows the use in hard to reach areas
• also suitable for vent and drain screws on plastic coolers on BMW, Ford, etc.

Technical data:

Length: 94 mm
Gross weight: 90 g
Output profile: Slot SL
Material: Carbon Steel
Output profile size: 14 x 1,7
Packaging suitable for wall hanging: Yes

• knurled

Technical data:

Drive profile size, metric: 12,5 mm
Drive profile size, inch: 1/2 "
Output profile size: M6
Material: Chrome Vanadium Steel
Output profile: Spline (for XZN)
Length: 53 mm
Gross weight: 80 g
Drive profile: Internal square

• designed to remove and install the fuel tank sensor locking ring
• suitable for e. g. Audi A4 (2008-2016), A6 (2008-2016), A6 (2005-2011), A8 (1994-)
• to be used as OEM T40068A, 3342

Technical data:

Drive profile size 1, metric: 21 mm
To be used as OEM1: 3342 | T40068A Audi
Drive profile 2: Internal square
Drive profile size 2, metric: 12,5 mm
Gross weight: 664 g
Drive profile 1: External hexagon
Drive profile 2, inch: 1/2 "

• knurled

Technical data:

Drive profile size, metric: 12,5 mm
Drive profile size, inch: 1/2 "
Drive profile: Internal square
Gross weight: 90 g
Material: Chrome Vanadium Steel
Output profile size: M9
Output profile: Spline (for XZN)
Length: 55 mm
Surface finish: Satin chrome plated

includes the following pullers:

• ball joint extractor, 2 steps
  • for separating of ball joints on steering and suspension
  • two step extractor for use on most cars and light commercial vehicles
  • offset lever provides a maximum extracting range
  • jaw opening: 16 - 20 mm
  • extracting range: 2 steps, max. 35 / 56 mm
  • spindle: M16 x 1.5
  • drive: 21 mm outer hexagon
  • forged & galvanized

• ball joint extractor
  • for removing track rod end from the steering arm
  • jaw opening: 19 mm
  • extracting range: max. 50 mm
  • spindle: M12 x 1.75
  • drive: 18 mm outer hexagon
  • forged & galvanized

• ball joint extractor
  • for separating of ball joints on steering and suspension
  • jaw opening: 20 mm
  • extracting range: max. 58 mm
  • spindle: M14 x 1.5
  • drive: 19 mm outer hexagon
  • forged & galvanized

Technical data:

Diameter: 365 mm
Material: Polypropylene (PP)
Gross weight: 350 g
Height: 110 mm

• knurled

Technical data:

Material: Chrome Vanadium Steel
Drive profile: Internal square
Gross weight: 70 g
Drive profile size, inch: 3/8 "
Output profile size: M7
Length: 100 mm
Drive profile size, metric: 10 mm
Surface finish: Satin chrome plated
Packaging suitable for wall hanging: Yes
Output profile: Spline (for Ribe)

• for car body work and tire service
• with square bar steel handle
• serrated surface for secure grip
• non-sparkling due to uniformly rubber cover
• special absorbing effect through steel balls in the hammer head
• substantially higher blow effect than in conventional hammering
• for conservative working with less recoil

Technical data:

Head diameter: 50 mm
Gross weight: 804 g
Stem length: 250 mm
Length: 310 mm