Pullers

includes the following pullers:

• ball joint extractor, 2 steps
  • for separating of ball joints on steering and suspension
  • two step extractor for use on most cars and light commercial vehicles
  • offset lever provides a maximum extracting range
  • jaw opening: 16 - 20 mm
  • extracting range: 2 steps, max. 35 / 56 mm
  • spindle: M16 x 1.5
  • drive: 21 mm outer hexagon
  • forged & galvanized

• ball joint extractor
  • for removing track rod end from the steering arm
  • jaw opening: 19 mm
  • extracting range: max. 50 mm
  • spindle: M12 x 1.75
  • drive: 18 mm outer hexagon
  • forged & galvanized

• ball joint extractor
  • for separating of ball joints on steering and suspension
  • jaw opening: 20 mm
  • extracting range: max. 58 mm
  • spindle: M14 x 1.5
  • drive: 19 mm outer hexagon
  • forged & galvanized

Technical data:

• for dismantling of bearings installed in a blind hole
• is used when repairing gearboxes, for example

scope of delivery:

• slide hammer, length 290 mm
• 2-feet puller with spindle
• spreader claws for bearings with inner diameter of 5 - 52 mm

Technical data:

Scope of delivery:

• Puller, 2-legs, 75 mm, reversible
• Puller, 3-legs, 100 mm, reversible
• Puller, 3-legs, 150 mm, reversible

Technical data:

• suitable for removing bearings, bushings, sleeves, etc.
• especially suitable for dismantling blind holes

Scope of delivery:

• sliding hammer 1430 g, 370 mm
• Spreader claws, 10-14 mm
• Spreader claws, 15-19 mm
• Spreader claws, 18-25 mm
• Spreader claws, 25-32 mm

Technical data:

Technical data:

Technical data:

Technical data:

Technical data:

Technical data:

• for extracting / pulling ball joints of e.g. anti-roll bar, control arm, tie rod and other ball joints
• suitable for many automobiles and light trucks from Ford, Volkswagen, Mercedes-Benz, Audi, Skoda, Citroen, Peugeot, Renault, Fiat, Mazda, Toyota etc.
• also suitable for pulling bearings and bushings

scope of delivery:

• 2-arm tie rod ball joint & drop arm puller
  • opening: 33 mm / width: 28 mm
  • opening (inside): 55 mm / height (inside): 55 mm
  • spindle: M16 / drive: 19 mm outer hexagon
  • forged & galvanized
• 2-arm tie rod ball joint & drop arm puller
  • opening: 18 mm / width: 18 mm
  • opening (inside): 45 mm / height (inside): 50 mm
  • spindle: M16 / drive: 19 mm outer hexagon
  • forged & galvanized
• tie rod ball joint extractor
  • opening: 18 mm / width: 28 mm
  • height: 50 mm / spindle M12 x 1.75
  • drive: 19 mm outer hexagon
  • forged & galvanized
• control arm ball joint & tie rod ball joint extractor
  • opening: 20-22 mm / length: 155 mm
  • extracting range: 2 steps max. 30 or 55 mm
  • drive: 21 mm outer hexagon
• 2-arm bearing puller, adjustable
  • leg wide: 16 mm / length: 160 mm
  • spindle: M14 / leg (inside): 75 mm
  • leg height (inside): 75 mm
  • drive: 17 mm outer hexagon

Technical data:

• suitable as inside and outside puller

scope of delivery:

• 3 puller arm sets (3 pcs. per set) for clamping depth of 100, 200 and 300 mm

Technical data:

scope of delivery:

• hydraulic spindle
• traverse 100 mm
• traverse 150 mm
• traverse 200 mm
• headpiece for 2-legs pullers
• headpiece for 3-legs pullers
• 2 extensions
• 2 separators from 20 - 105 mm

Technical data:

• adjustable and suitable for most car and truck types

Technical data: